Mini Excavators for Sale in Ontario

Start with the work and the route into the site

Choosing a mini excavator starts with a written job list: the trench or excavation, the route into the property, where spoil will go and how the machine will move between jobs. Measure the narrowest opening and note corners, overhead obstacles and the working area beyond the entrance. Bring a sketch or photographs to your model enquiry. A machine that passes through an opening still needs a suitable place to work; an entrance measurement does not describe the whole site.

Use this page to shortlist compact models. For the broader excavator range, including larger crawler machines, use the excavators category. For a landscaping project, read the Toronto landscaping guide alongside this comparison. Treat the size bands below as starting points for a discussion, rather than a recommendation that every machine in a band can complete the same job. Depth, width, tool choice and the actual configuration all belong in the enquiry.

Under 2 t: ER620H for an access-led shortlist

The ER620H model page lists an operating weight of 1,950 kg, an overall width of 990 mm, a maximum dig depth of 2,330 mm and a bucket capacity of 0.04 m³. Its engine is Kubota D902. Use that width as a starting measurement when considering a garden entrance or a restricted route into a yard. Check the actual machine and attachment envelope against your site measurements instead of assuming the published machine width describes every setup.

For garden and landscape enquiries, describe the excavation, access surface, proposed working position and destination for the excavated material. Ask whether the planned bucket and any other tool suit the work. If access is the reason for considering this size, keep the access sketch with the model specification throughout the discussion. Do not select a model solely because it is the smallest in the table; the excavation and the working area still need their own assessment.

Around 3–4 t: ER627H and ER636H

ER627H sits just below the nominal 3 t band at 2,950 kg; ER636H is listed at 3,800 kg. Their published maximum dig depths are 2,860 mm and 3,110 mm, and their bucket capacities are 0.06 m³ and 0.12 m³ respectively. The model pages identify Kubota D1105 for ER627H and Kubota D1703 for ER636H. Compare the exact figures, rather than reading the model number as a weight or engine designation.

For a landscaping or utility-trench shortlist, record the required excavation profile, access restrictions and where the machine could stand. Compare those requirements with each model page and ask about the intended tool. Include any work close to fences, buildings or existing services in the description. A published maximum dig depth is a comparison figure, not a complete excavation plan or permission to dig near a service. Resolve the site requirements before choosing between these models.

5–8 t enquiries: ER655H, with ER680H above the band

ER655H is listed at 5,900 kg with a 3,492 mm maximum dig depth, 0.18 m³ bucket and 1,980 mm overall width. Its engine is Yanmar 4TNV86CT. ER680H is listed at 8,580 kg with a 4,135 mm maximum dig depth, 0.28 m³ bucket and 2,240 mm overall width, using a Yanmar 4TN98C engine. Keep the ER680H actual weight in the comparison: it exceeds the upper edge of the nominal band.

When considering these models for landscape excavation or utility work, explain what makes the smaller shortlist insufficient. Is it the required excavation profile, the planned tool, the route or the working area? Discuss those constraints together. Do not infer lifting capacity, production speed or ground-bearing suitability from operating weight and bucket volume. Those questions require the relevant machine documentation and a site assessment. A larger model also needs its own transport review, rather than reusing the plan made for a smaller excavator.

Trailer and towing: assess the complete combination

Ontario’s official towing handbook says to check that the vehicle can tow both the trailer and the intended load, and that the trailer and hitch meet the handbook requirements. It defines trailer gross weight as the trailer plus its load. Use that complete combination when reviewing transport; the excavator operating weight alone does not settle the towing question. Read the current official guidance and the documentation for the actual towing equipment before arranging a move.

Bring the exact excavator configuration, attachment list and truck-and-trailer details to the transport discussion. Ask the transport provider to review the combination and route. The widths in this table describe the machine’s published overall width; they do not identify a suitable trailer or approve the loaded combination. This page makes no model-specific towing recommendation. If the transport arrangement is unresolved, resolve it alongside the model enquiry rather than after the equipment decision.

Buckets, augers and breakers: confirm the carrier fit

Consider the digging bucket alongside the work, then ask about an auger for a drilling enquiry or a breaker for a breaking enquiry. ArcPath’s attachment directory lists buckets, augers and breakers among its tool categories, but its listed tools are specified against the mini track loader carrier family. Other carriers, including SDLG equipment, require a fitment review before ordering. The directory is a reference for that discussion, not evidence that a listed tool fits an ER excavator.

Send the exact carrier model, interface and hydraulic details with the intended application. Ask for the tool-and-carrier combination to be reviewed before selecting an attachment. Keep a digging-machine enquiry separate from a material-moving enquiry: if your work mainly concerns moving or preparing material, also explore the compact track loader category before settling on an excavator. Compare the job descriptions and relevant model documentation rather than treating those categories as interchangeable.

Read each column before making an enquiry

Read the model page linked in each table row. Keep operating weight, maximum dig depth, bucket capacity, overall width and engine as separate comparison fields. A gap in the published information is a question to ask, rather than a reason to copy a value from a neighbouring model. Where a page repeats a specification in a secondary field, this table follows the named Specifications section; ask TerraX to confirm any discrepancy for the machine under consideration.

For your enquiry, include the shortlisted model, site access, excavation profile, intended tools and transport questions. Use the contact link on this page to discuss that configuration with TerraX in Toronto. You can also browse the industrial category to understand the wider equipment offering. Keep your enquiry tied to the actual work and the exact machine documentation so the next conversation can address the remaining decisions directly.

Equipment and planning guides

• All excavators
• Toronto landscaping guide
• Compact track loaders
• Industrial equipment